Редактирование: Guide to Ordnance (раздел)

== [[File:Hud-fire.png]] Heat Mix Production ==
For reactionless explosions and tritium bombs, we will need a heat mixture. Thermomachine does the job but not very well. 

[[File:Gas Mixer Setup.png|thumb|Gas Mixer Setup]]
[[File:Heat Pump Setup.png|thumb|Heat Pump Setup]]

Collecting the results of a burn chamber is quicker more often than not, but is very time sensitive and tends to result in a mix with lower temperature than this method.

# Prepare a gas mixer contraption as pictured.
#: <b>Why:</b> We are preparing a burn canister for the heat.
# Wrench a [[File:Plasma_Canister.png]] plasma can on the main node.
#: <b>Why:</b> A burn mix needs plasma as the fuel.
# Wrench an [[File:O2_Canister.png]] oxygen can on the side node.
#: <b>Why:</b> And oxygen as the oxidizer.
# Wrench an empty [[File:Canister.png]] can on the output node.
#: <b>Why:</b> We will heat the plasma and oxygen up inside a canister so the heat is contained inside and not lost to environment like in chamber burns. Read more [[Guide_to_Atmospherics#Superconduction|here]]
# Pump in a 60-40 mix of plasma - oxygen with the [[File:Atmos_mixer.png]] mixer. Main node to 60, side node to 40.
#: <b>Why:</b> This is just <i>one</i> recipe, feel free to experiment and use another one.
# Unwrench and hook the resulting canister up to a [[File:Freezer.gif]] thermomachine. Turn shielding on.
#: <b>Why:</b> The heat will exceed the 10 K Kelvin limit allotted to canisters. Without shielding it will melt.
# Set the thermomachine to maximum temperature and unwrench the canister once it exceeds the target temperature.
#: <b>Why:</b> Get a higher temperature for better starting efficiency if you can, but anything above 100 Celcius works fine. Unwrenching is to ensure that the thermomachine doesn't end up cooling the burn canister.
# Prepare a heat pump contraption as pictured.
#: <b>Why:</b> Simple heat is not enough, we need to have the heat stored in a very dense format (plasma).
# Wrench a [[File:Plasma_Canister.png]] plasma canister to the output node, unwrench it.
#: <b>Why:</b> A whole plasma canister is too much! We only need a few moles to fully fill a tank. Less plasma also means less heat capacity which means higher temperature.
# Wrench a new [[File:Canister.png]] canister at the output node. Turn shielding on.
#: <b>Why:</b> This will allow us to only heat the moles left in the heat pump instead of the whole plasma canister. Shielding once again for temperature protection.
# Wrench the previous burn canister into the input node of the temperature pump
#: <b>Why:</b> We will transfer the heat from the burn can to the plasma.
# Turn on the [[File:Temperature Pump.png]] heat pump. Maximize it
#: <b>Why:</b> This will actually transfer the heat from the old canister to the new one, compacting the energy stored to a higher specific heat.
# Grab a [[File:Plasma_tank.png]] tank from a [[File:Tank_Dispenser.png]] tank dispenser, empty it with a portable scrubber.
#: <b>Why:</b> We will put the hot plasma into this tank so it can be attached to the [[File:Explosivebombthatgoesboom.png]] TTV. Best make sure its empty first so cold plasma doesn't equalize with the hot one, making an at best lukewarm tank.
# Insert the tank into the canister, crank the pressure up, open the valve. In that order.
#: <b>Why:</b> This will fill the tank with the necessary plasma. We are finally done.
# Do a last check on the tank using an [[File:Analyzer.png]] analyzer. There should be a hot (20k Kelvins +) mixture of pure plasma in the tank, with the pressure reading 2533 kPa.
#: <b>Why:</b> If you mess up, best know why and where exactly.